24-12-2016, 14:35
|
#1
|
Inactive
Join Date: Dec 2016
Posts: 3
|
Unable to connect
Hi all I am seeking some advice ,
I have just moved my TiVo box and router from one side of the room to another , I purchased a standard satalite cable which I have attached to my virgin box on the wall and ran the cable behind the skirting board
When I connect my router on its own , it works correctly , as soon as I plug in the spliter and connect the router and attached by a cable one end to the splinter the other to the router it stops working (. No blue arrow)
I have bought a new splinter box this morning think that might be the fault and I have also bought new cabelsv( f type) thinking it might be that , but still nothing
If I revert to just plugging the router direct to the main cable it connects , Any ideas
|
|
|
24-12-2016, 15:52
|
#2
|
cf.addict
Join Date: May 2010
Posts: 336
|
Re: Unable to connect
Your new cable and splitter probably isn't up to VM spec and causing signal issues. Was my pet hate as a service tech people using their own cabling etc, and when I was a network engineer it was just as bad because it would send noise out to the neteork
|
|
|
24-12-2016, 15:57
|
#3
|
Inactive
Join Date: Dec 2016
Posts: 3
|
Re: Unable to connect
Can you recommend what cable I should get etc please and where from ?
|
|
|
24-12-2016, 15:57
|
#4
|
cf.mega poster
Join Date: Jun 2003
Posts: 8,903
|
Re: Unable to connect
Either the cable you bought is the wrong type, or your signal level isn't high enough to get through the extra length. Get Virgin Media out to do it, and they'll make sure the right parts are used and the signal level is correct.
ps. Welcome to the forum!
|
|
|
24-12-2016, 15:58
|
#5
|
Inactive
Join Date: Dec 2016
Posts: 3
|
Re: Unable to connect
The cable was pre made 10 meter length and was bought from maplins
|
|
|
24-12-2016, 16:30
|
#6
|
cf.addict
Join Date: May 2010
Posts: 336
|
Re: Unable to connect
Quote:
Originally Posted by Gary1967
Can you recommend what cable I should get etc please and where from ?
|
RG6, Virgin Media
|
|
|
24-12-2016, 20:46
|
#7
|
Inactive
Join Date: Dec 2016
Posts: 15
|
Re: Unable to connect
Quote:
Originally Posted by vm_tech
RG6, Virgin Media
|
The cost of £99 call out charge is reasonable considering its a no hassle move. The cost of buying various cables etc and the time taken to do it is a complete waste.
Why do people insist on moving virgin equipment but wont consider moving sky dish?
|
|
|
28-12-2016, 19:58
|
#8
|
Cable Guru
Join Date: Jun 2004
Location: Scotland
Age: 41
Services: Virgin Media Gig1 RFOG, TV360, Stream, GoFibre 1Gb
Posts: 1,049
|
Re: Unable to connect
By the sounds of it, its a signal level issue. You may already have been borderline with your current cabling setup so perhaps a powered HDU setup is required. I could only ever recommend a VM engineer carry out any work here. Please try and avoid using satellite cable as it generally is not up to the standard required and causes ingress into the Virgin Media network, causing issues for you and your neighbours.
__________________
Access Network Innovation @ Liberty Global/Virgin Media
All comments are my own opinion and not a direct expression of LG/VM.
|
|
|
29-12-2016, 10:23
|
#9
|
Perfect Soldier
Join Date: Mar 2009
Location: Worthing West Sussex
Age: 66
Services: VM 500M SH3 thingy
in modem mode
XL TV V6 Sony Bravia smart TV and M phone
Posts: 10,995
|
Re: Unable to connect
It's usually a good plan to jot down the signal levels from the diagnostic pages in the TIVO and hub and recheck them after moving equipment as any reduction of signal outside the specification required by the devices will impact the service. As stated above you MUST use cable that is to/exceed VMs specification: Triple shielded and low loss e.g. Webro HD 100 with good quality connectors and then only short distances.
__________________
History is much like an endless waltz: The three beats of war, peace and revolution continue on forever.
However history will change with my coronation - Mariemaia Khushrenada
|
|
|
29-12-2016, 11:30
|
#10
|
cf.addict
Join Date: May 2010
Posts: 336
|
Re: Unable to connect
Quote:
Originally Posted by heero_yuy
It's usually a good plan to jot down the signal levels from the diagnostic pages in the TIVO and hub and recheck them after moving equipment as any reduction of signal outside the specification required by the devices will impact the service. As stated above you MUST use cable that is to/exceed VMs specification: Triple shielded and low loss e.g. Webro HD 100 with good quality connectors and then only short distances.
|
I haven't looked in the diagnostics page on a STB for years, but I believe it doesn't show signal levels. The signal level isn't the be all and end all, the quality is much more important, the signal levels could be out of spec but as long as there are no errors coming through, it should be alright
|
|
|
29-12-2016, 11:56
|
#11
|
Perfect Soldier
Join Date: Mar 2009
Location: Worthing West Sussex
Age: 66
Services: VM 500M SH3 thingy
in modem mode
XL TV V6 Sony Bravia smart TV and M phone
Posts: 10,995
|
Re: Unable to connect
Quote:
Originally Posted by vm_tech
I haven't looked in the diagnostics page on a STB for years, but I believe it doesn't show signal levels. The signal level isn't the be all and end all, the quality is much more important, the signal levels could be out of spec but as long as there are no errors coming through, it should be alright
|
IIRC on tech stuff page 2 our VHD box shows the return dbmv and the AGC level but not the downstream level directly.
__________________
History is much like an endless waltz: The three beats of war, peace and revolution continue on forever.
However history will change with my coronation - Mariemaia Khushrenada
|
|
|
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
All times are GMT +1. The time now is 07:36.
|