24-11-2016, 14:22
|
#1
|
Inactive
Join Date: Dec 2005
Location: Bromsgrove, Worcestershire
Age: 49
Services: Talk Talk 1.5mb wishing it was Virgin 20mb
Posts: 2,462
|
Loft Problem - Advice
Hi Guys N Gals
Ok I am basically going to be boarding my loft, and I want to fit some retractable ladders, but a lot of them say they need a clearance arc of so much room.
My problem is in my loft (See Pics), There's a massive 4inch bearer spanning the width of the two purlins. I can only assume this is to stop the eaves sagging at the base. There's no structural reason for it being there apart from that.
I basically dont like it but i realise that its there for some purpose. If i cut the center of it out, 3ft, and put vertical bearers in, then strengthen the base, would this suffice as an alternative?
The property is a 1960s build. Loft is in very good condition.
|
|
|
24-11-2016, 15:00
|
#2
|
cf.mega poster
Join Date: Jun 2003
Location: Kairdiff-by-the-sea
Age: 68
Services: TVXL BBXL Superhub 2ac (wired) 1Tb Tivo
Posts: 9,837
|
Re: Loft Problem - Advice
Guy up the road did roughly what you suggest. The roof developed a dip in weeks. Expensive to put right with hydraulic jacks and a access hole cut through the roof.
The roofers opened another hatch for him to install the (prebought) ladder set in.
Be careful as some houses in that period used non-standard joist spacings that meant the T&G sheets you can buy won't fit without fitting noggings, etc.
|
|
|
24-11-2016, 16:03
|
#3
|
Trollsplatter
Cable Forum Team
Join Date: Jun 2003
Location: North of Watford
Services: Humane elimination of all common Internet pests
Posts: 37,010
|
Re: Loft Problem - Advice
Leave well alone. As Taf said, fixing any problems you might create will be fearsomely expensive. Unless you're competent as a builder/roofer (and clearly you're not), you should confine your DIY to the simplest projects, such as installing boards and ladders that don't impact on anything else in the loft at all.
|
|
|
24-11-2016, 16:03
|
#4
|
Perfect Soldier
Join Date: Mar 2009
Location: Worthing West Sussex
Age: 67
Services: VM 500M SH3 thingy
in modem mode
XL TV V6 Sony Bravia smart TV and M phone
Posts: 11,012
|
Re: Loft Problem - Advice
It might not look it but that is a major triangulation element in the roof structure. It's less common as most site constructed, as opposed to truss, roofs have twin struts to the centre where there is usually a supporting spine wall through the centre of the property. My roof has two sets of these and they support considerable load, you only have to tap them with a hammer to hear that.
I would get the advice of a structural engineer before interfering with it in any way.
__________________
History is much like an endless waltz: The three beats of war, peace and revolution continue on forever.
However history will change with my coronation - Mariemaia Khushrenada
|
|
|
24-11-2016, 16:33
|
#5
|
Inactive
Join Date: Dec 2005
Location: Bromsgrove, Worcestershire
Age: 49
Services: Talk Talk 1.5mb wishing it was Virgin 20mb
Posts: 2,462
|
Re: Loft Problem - Advice
This is a replica of the loft and what i want to do...
|
|
|
24-11-2016, 16:47
|
#6
|
Sad Doig Fan!
Join Date: Aug 2007
Location: Barry South Wales
Age: 68
Services: With VM for BB 250Mb service.(Deal)
Posts: 11,670
|
Re: Loft Problem - Advice
Quote:
Originally Posted by Barewolf
This is a replica of the loft and what i want to do...
|
Which will effectively remove the structurly sound triangulation. You obvviously don't know what you are doing so as above, leave well alone.
|
|
|
24-11-2016, 16:52
|
#7
|
Inactive
Join Date: Dec 2005
Location: Bromsgrove, Worcestershire
Age: 49
Services: Talk Talk 1.5mb wishing it was Virgin 20mb
Posts: 2,462
|
Re: Loft Problem - Advice
i dont know what im doing with lofts and roofs, but my dad said he cant see the point in it, and hes been a builder for most of his life.
it looks to me like its to stop the eaves sagging, but thats the only bearer in the loft, and what i suggested to do would easily hold any strain on the purlins surely
|
|
|
24-11-2016, 17:06
|
#8
|
Trollsplatter
Cable Forum Team
Join Date: Jun 2003
Location: North of Watford
Services: Humane elimination of all common Internet pests
Posts: 37,010
|
Re: Loft Problem - Advice
Quote:
Originally Posted by Barewolf
i dont know what im doing with lofts and roofs, but my dad said he cant see the point in it, and hes been a builder for most of his life.
it looks to me like its to stop the eaves sagging, but thats the only bearer in the loft, and what i suggested to do would easily hold any strain on the purlins surely
|
And yet you're not sure. Even after speaking to your dad.
Seriously: don't. Not without consulting a structural engineer, and definitely not based on the encouragement you're trying to get off random strangers on the internet.
|
|
|
24-11-2016, 17:35
|
#9
|
cf.mega poster
Join Date: Jun 2003
Location: Kairdiff-by-the-sea
Age: 68
Services: TVXL BBXL Superhub 2ac (wired) 1Tb Tivo
Posts: 9,837
|
Re: Loft Problem - Advice
Our house, for example, has an inner wall of insulation blocks that are so flimsy you could push your finger into them. They are not designed to support weight at all. so the purlins do so. Supported at each end by the end walls, and along their length by purlin braces, either diagonals and/or across the width of the roof.
---------- Post added at 17:35 ---------- Previous post was at 17:30 ----------
As heero_yuy said, you only have to tap them with a hammer to hear them "ping" as they are under a large load.
Collar ties often cross from purlin to purlin when the purlin braces are not diagonal but vertical.
In some loft conversions, the purlins are replaced by steel girders, a major expense of the job, but they allow the removal of ties and braces.
|
|
|
24-11-2016, 18:06
|
#10
|
Inactive
Join Date: Dec 2005
Location: Bromsgrove, Worcestershire
Age: 49
Services: Talk Talk 1.5mb wishing it was Virgin 20mb
Posts: 2,462
|
Re: Loft Problem - Advice
Quote:
[/COLOR]As heero_yuy said, you only have to tap them with a hammer to hear them "ping" as they are under a large load.
Collar ties often cross from purlin to purlin when the purlin braces are not diagonal but vertical.
In some loft conversions, the purlins are replaced by steel girders, a major expense of the job, but they allow the removal of ties and braces.
|
Those purlin bracing is what i am proposing to do in my loft, they distribute any weight along the joists which is effectively what the joist is doing now in the center.
I find it odd there's only one 4x2 joist between the purlins. It doesn't appear to be doing anything significant that couldn't be worked around by distributing the weight down and across the joists, it would basically be the same and evenly distributed.
my Dad seems to thing they could have just put that there to hold the purlins in place while they cemented them in, he doesnt think its anything major.
I asked in the forum incase anyone is a structural engineer, or a builder, that could confirm my theory.
|
|
|
24-11-2016, 18:09
|
#11
|
Guest
Location: newcastle upon tyne
Services: Sky Q silver bundle
Sky Q 2TB box
Sky Q mini box
Sky fibre unlimited
Sky Talk evenings and week
Posts: n/a
|
Re: Loft Problem - Advice
the best thing you have done is ask before blindly ripping timbers out ,i have seen so many disasters and repaired a few .Your roof type is not of the modern prefab type fetched on the back of lorries it is made on site by roofing joiners who did not waste time putting unnecessary timbers in ,every piece does a job .That particular timber is responsible for transferring the weight from the ridge through the supports shown in your other diagrams into the purlins.It would be an easy enough job to move the hatch ,is that not an option ?
|
|
|
24-11-2016, 18:34
|
#12
|
Inactive
Join Date: Dec 2005
Location: Bromsgrove, Worcestershire
Age: 49
Services: Talk Talk 1.5mb wishing it was Virgin 20mb
Posts: 2,462
|
Re: Loft Problem - Advice
Quote:
Originally Posted by martyh
the best thing you have done is ask before blindly ripping timbers out ,i have seen so many disasters and repaired a few .Your roof type is not of the modern prefab type fetched on the back of lorries it is made on site by roofing joiners who did not waste time putting unnecessary timbers in ,every piece does a job .That particular timber is responsible for transferring the weight from the ridge through the supports shown in your other diagrams into the purlins.It would be an easy enough job to move the hatch ,is that not an option ?
|
No room in the hall to move the hatch, and even if i did i would still have a beam running the width of the loft which you have to step over at waist height.
My neighbour is a gas engineer, hes popping round tomorrow and hes converted his loft, exact same layout, so i will ask him what he did.
Pretty sure though that 4 angled 3x2 from both purlins down to the joists would do the same job if not more than that single beam. But thats just me and common sense. i aint paying £300 for a structural engineer to take one look at it and say it serves no purpose.
|
|
|
25-11-2016, 02:38
|
#13
|
Dr Pepper Addict
Cable Forum Team
Join Date: Oct 2003
Location: Nottingham
Age: 61
Services: Flextel SIP : Sky Mobile : Sky Q TV : VM BB (1000 Mbps) : Aquiss FTTP (900 Mbps)
Posts: 27,838
|
Re: Loft Problem - Advice
Thats your choice of course, but if you do cause expensive damage, chances are your house insurance will not cover it.
__________________
Baby, I was born this way.
|
|
|
25-11-2016, 15:06
|
#14
|
Inactive
Join Date: Jun 2003
Location: Stockport
Age: 46
Posts: 966
|
Re: Loft Problem - Advice
You'll be fine just removing it and doing as you have drawn.
__________________
Gamertag : bulkylad
|
|
|
25-11-2016, 15:36
|
#15
|
Sad Doig Fan!
Join Date: Aug 2007
Location: Barry South Wales
Age: 68
Services: With VM for BB 250Mb service.(Deal)
Posts: 11,670
|
Re: Loft Problem - Advice
Quote:
Originally Posted by Bulky
You'll be fine just removing it and doing as you have drawn.
|
Are you accepting liability along with your advice?
|
|
|
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
All times are GMT +1. The time now is 15:44.
|