Has Superhub a WPS button that can blink red&blue?
The Superhub gives very poor wifi coverage upstairs, so I have obtained a Huawei WS320 wifi repeater as an interim measure before buying a router for modem mode.
The Huawei manual and posts by huawei reviewers say: - press the WPS button on the router. - press button on the Huawei and wait for the green ready light to come on - move the huawei repeater to a place where wifi is weak to boost signal The green light on the Huawei did not come on. According to article 'Using the Push N Connect button to add a WPS client to the Virgin Media Super Hub' at VM http://help.virginmedia.com/system/s...ER_TYPE=Cable: '1. Press and hold the Virgin Media button on the Super Hub for two seconds, and then release the button (holding down the button for too long will disable the wireless signal altogether). The Virgin Media light should blink red and blue for a period of up to two minutes while the Super Hub searches for nearby compatible WPS devices.' I pressed the button on the Superhub for 2-3 seconds (the one with the Virgin logo on the front panel), but it did not blink red and blue. Tried many times. I phoned Virgin customer support and was told that the Superhub does not have a WPS button (older (super)hubs had he said). What is the truth? Ken |
Re: Has Superhub a WPS button that can blink red&blue?
Quote:
|
Re: Has Superhub a WPS button that can blink red&blue?
The Huawei repeater works with the Superhub in router mode. After it has been intialised to work with the Superhub downstairs, the Huawei repeater would be moved upstairs to the room where the wifi signal is weakest. The Superhub router-part will still feed wifi to equipment downstairs.
VM installed the Superhub here in January 2012. Would that be a 'new' Superhub? Were the old Superhubs different and when did VM stop using them? Ken |
Re: Has Superhub a WPS button that can blink red&blue?
Quote:
|
Re: Has Superhub a WPS button that can blink red&blue?
If you are having problems with the physical button, you can try the admin interface one. It's under Advanced Settings > WPS Settings and then click 'WPS Sync'
You can also double check there that WPS access is enabled |
Re: Has Superhub a WPS button that can blink red&blue?
There is only one version of the Superhub available at present and they all have "the button"
There was some scandal about WPS security holes which resulted in a lot of manufacturers disabling it though... |
Re: Has Superhub a WPS button that can blink red&blue?
After having pressed the button on the front panel of the Superhub for about 0.5 seconds the button starts blinking in blue. Still pressing button, after another 1.5-2.0 seconds the button reverts to solid blue. There is no red colour blinking at all during this period or after stopping pressing the button.
Using the browser interface shows that security mode is WPA-AUTO. Accessing WPS settings on Advanced settings via the browser interface shows: - WPS Enabled: set/on/true (in checkbox) - WPS button: selected (by radiobutton) According to the Help text for the WPS Settings dialog these two settings imply that the WPS/Logo button should work. I also clicked the WPS Sync button in the WPS Settings dialog. Should the physical button blink in red and blue after this (to show the hub is in device detection mode)? It did not. I am beginning to think the WPS is not working on my Superhub. Is there anything else I can do to demonstrate this before I contact VM customer support again? If someone on this forum could press this button and let me know that it definitely should blink in red and blue that of course would make my case stronger. Ken |
Re: Has Superhub a WPS button that can blink red&blue?
Try WPS on another device? Easiest way to see if WPS is working is to try and use it.
|
All times are GMT +1. The time now is 23:15. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.