PDA

View Full Version : Network cables


Sparks
05-06-2005, 19:30
At the moment I have two PCs networked with a x-over cable (cable is under floor an inside wall). I am thinking of fitting a router and don't want to run a new straight through cable. Is there an adaptor that will change from X to strait?, or any other suggestions. Thx.

bmxbandit
05-06-2005, 19:33
if you buy a router with an uplink port, the x-over will plug directly into that. not sure if these are easly avalable though.

iyou could te a normal cable to the end and pull it through, shouldn't be too hard.

iain_herts
05-06-2005, 19:40
or u could always cut off the old connections and put some new 1's on to make it a patch cable worth a go i think but dunno how much the stuff would cost tho.

bmxbandit
05-06-2005, 19:42
or u could always cut off the old connections and put some new 1's on to make it a patch cable worth a go i think but dunno how much the stuff would cost tho.
...more than a new cable!

paulyoung666
05-06-2005, 19:42
iirc you can buy a gender changer to make it straight thru :)

Sparks
05-06-2005, 20:12
All this is a grey area for me so i will have to look into it. Router with a uplink port could be easiest if i could get one. I've looked at some gender changers but cant see one with the right connections.

Paul K
05-06-2005, 20:17
One of these (http://www.maplin.co.uk/Module.aspx?ModuleNo=32423&TabID=1&C=SEO&U=StaticPages&doy=search&MenuName=UTP%20CROSSOVER%20ADAPTOR%20(MALE%20-%20FEMALE))?

Q: If this can be used to change a crossover cable to a straight cable what end do you plug it on as the ends of a crossover cable are different (smoothdude: 27/01/2005 )
A: The adapter will reverse the current cable eg straight through to crossover and vice versa, end does not matter.

Derek
05-06-2005, 20:18
Would this (http://www.maplin.co.uk/Module.aspx?ModuleNo=32423&doy=5m6D) do the trick?

EDIT: Really must hit that submit button a little faster next time. :)

Paul K
05-06-2005, 20:20
Would this (http://www.maplin.co.uk/Module.aspx?ModuleNo=32423&doy=5m6D) do the trick?

EDIT: Really must hit that submit button a little faster next time. :)
Since it's the same as my link then I would say yes but I am biased ;)

Graham M
06-06-2005, 00:21
Most routers, this includes mine, which is a Belkin, these days have Auto-Detecting Ports that will try both Cross-Over and Straight paths to see which one works to make the job a little easier.

Millay
06-06-2005, 00:50
Most routers, this includes mine, which is a Belkin, these days have Auto-Detecting Ports that will try both Cross-Over and Straight paths to see which one works to make the job a little easier.

Was just going to say that myself, you will be hard pushed to by a switch/router that is not autosensing nowadays....

Sparks
06-06-2005, 17:18
Most routers, this includes mine, which is a Belkin, these days have Auto-Detecting Ports that will try both Cross-Over and Straight paths to see which one works to make the job a little easier.
Being as I have to buy a router anyway my best bet would be to buy one that has Auto Detecting ports and i haven't seen any that state this. So can someone point me in the direction of a good make and model as i don't want to have to send it back if it doesn't work. Also it is only required for two networked PCs, thanks in advance.

bmxbandit
06-06-2005, 17:23
Was just going to say that myself, you will be hard pushed to by a switch/router that is not autosensing nowadays....
damn my dated equipment (and knowledge!)

:dunce:

Graham M
06-06-2005, 17:23
a Belkin F5D7230-4 is what I own, its done me well

Paul K
06-06-2005, 17:30
This one does it according to the support pdf
http://www.linksys.com/international/product.asp?coid=6&ipid=367
ftp://ftp.linksys.com/international/datasheets/befsr41v3_uk_ds.pdf

Sparks
06-06-2005, 20:10
I've taken onboard all your comments and I think I'll go for the Linksys BEFSR41 router as it has ADPs. Now I'll have to try again to get my ENET port working on my NTL Home 100 modem. At the moment I'm having to use it's USB connection but thats another story and maybe another post.:confused:

Paul K
06-06-2005, 20:15
Normally switching from USB to ethernet just requires the PC to be powered down, sacm powered off, connect the ethernet to PC and SACM, power up SACM, allow lights to lock, power up PC.
Notice the word normally lol ;)

Sparks
07-06-2005, 17:06
Normally switching from USB to ethernet just requires the PC to be powered down, sacm powered off, connect the ethernet to PC and SACM, power up SACM, allow lights to lock, power up PC.
Notice the word normally lol ;)
I've done all this, the ENET light is on in my NTL modem but I cannot ping out. I shouldn't have to change any settings should I?, after all it works OK with a USB connection. I've looked up previous posts on this subject but they don't hold the solution.

Paul K
07-06-2005, 17:23
Did you try the instructions here
http://homepage.ntlworld.com/robin.d.h.walker/cmtips/usb.html#usbswap
and
http://www.cableforum.co.uk/board/article.php?goto=lastcomment&v=1&a=13#comment132 ?

Sparks
07-06-2005, 19:39
Paul On looking at your links I noticed this about MAC addresses.

"Do not re-run any broadband installation software provided by your ISP. There is no need to re-register your cable modem account. However, for those ISPs which require the MAC address of the user's PC to be registered, this will be a necessary step, as the PC's MAC address will have changed".
Do you think this will apply in my case as this was not the PC that I had when I first registered my NTL b/band. If so will I need to delete this registration (somehow) and re_register using your second link,or what.
Sorry to be such a pain.